لیک مقالات دکتر علیرضا علافچیان

Core-Shell Fabrication of an Extra-Antimicrobial Magnetic Agent with Synergistic Effect of Substrate Ligand to increase the antimicrobial activity of Ag Nanoclusters

Authors

Seyede Zohre Mirahmadi-Zare, Ali R. Allafchian, S.A.H. Jalali

Publication date

2019

Journal

Environmental Progress & Sustainable Energy

Volume

38

Pages

237–245

Description

In this work, a novel antimicrobial agent is synthesized. The metal‐chelating ligand EDTA is incorporated into silver nanoparticles to form a new cluster system which is enhanced in its efficacy to eliminate bacteria. Magnetic nanoparticles of Fe3O4 were layer‐by‐layer coated with aminopropyltriethoxysilane, linked‐EDTA, and silver nanoclusters (Fe3O4@APTESEDTA@Ag), respectively. All steps of nanocomposite preparation were characterized by the TEM, field emission scanning electron microscope, X‐ray diffraction, Brunauer–Emmett–Teller, Vibrating Sample Magnetometer, and Fourier transform infrared. A sequential nucleophilic reaction applied for layer‐by‐layer fabrication of these antimicrobial units which could maintain the functionality of linked‐EDTA as EDTA chelator. The linked‐EDTA sequesters Ca2+ and Mg2+ ions effectively, thereby removing these metallic ions which are necessary for cell‐wall

Fabrication of tragacanth and water soluble tragacanth nanoparticles through electrospraying

Authors

Zhinoos Javadi, Hossein Tavanai, Alireza Allafchian, Mohammad Morshed

Publication date

2018/7

Journal

Polymers for Advanced Technologies

Volume

29

Issue

7

Pages

2036-2041

Description

This work reports the fabrication of tragacanth and water soluble tragacanth (WST) through electrospraying technique. Tragacanth is a biocompatible and biodegradable carbohydrate with a wide range of applications. Suspensions of tragacanth in water and water‐ethanol (70:30) were electrosprayed successfully. Moreover, deesterified tragacanth (WST), which is highly water soluble, was also successfully electrosprayed. The results showed that electrospraying technique is capable of producing tragacanth nanoparticles with an average size in the range of 30 to 50 nm, depending on the electrospraying conditions. Water soluble tragacanth gave rise to even smaller nanoparticles. It was also found that lowering feed rate, increasing nozzle‐ collector distance, and increasing voltage decrease the average size of the electrosprayed tragacanth nanoparticles. The molecular weight of tragacanth and WST was

Electrosprayed Cerium Oxide Nanoparticles

Authors

Pedram Bagherzadeh Azar, Hossein Tavanai, Ali Reza Allafchian

Publication date

2018/7/1

Journal

Journal of Electronic Materials

Volume

47

Issue

7

Pages

3779-3787

Publisher

Springer US

Description

Cerium oxide nanoparticles were fabricated via the calcination of electrosprayed polyvinyl alcohol (PVA)/cerium nitrate nanoparticles. The effect of material variables of PVA/cerium nitrate electrospraying solution, i.e. viscosity, surface tension and electrical conductivity, as well as important process variables like voltage, nozzle–collector distance and feed rate on cerium oxide nanoparticle size, are investigated. Scanning electron microscopy and Fourier-transform infrared (FTIR) spectroscopy analysis have also been carried out. The results showed that electrospraying of PVA/cerium nitrate (25% w/v) was only possible with PVA concentrations in the range of 5–8% w/v. With other conditions constant, decreasing PVA concentration, decreasing feed rate, increasing nozzle–collector distance and increasing voltage decreased the size of the final cerium oxide nanoparticles. The gross average size of all cerium

Fabrication of cellulose nanoparticles through electrospraying

Authors

Nastaran Kadivar, Hossein Tavanai, Alireza Allafchian

Publication date

2018/3/23

Journal

IET nanobiotechnology

Volume

12

Issue

6

Pages

807-813

Publisher

IET Digital Library

Description

This study reports the fabrication of cellulose nanoparticles through electrospraying the solution of cellulose in N,N-dimethylacetamide/lithium chloride solvent as well as investigating the effect of electrospraying conditions and molecular weight on the average size of electrosprayed nanoparticles. Electrospraying of cellulose was carried out with the following range for each factor, namely concentration = 1–3 wt%, voltage = 15–23 kV, nozzle–collector distance = 10–25 cm, and feed rate = 0.03–0.0875 ml/h. The smallest nanoparticles had an average size of around 40 nm. Results showed that lowering the solution concentration and feed rate, as well as increasing the nozzle–collector distance and applied voltage led to a decrease in the average size of the electrosprayed cellulose nanoparticles. Fourier transform infrared analysis proved that no chemical change had occurred in the cellulose structure

Preparation of amino silane magnetic nanocomposite by the sol-gel process and investigation of its antibacterial activity

Authors

Raana Hatami, Alireza Allafchian, Fathallah Karimzadeh, Mohammad Hosein Enayati

Publication date

2019/2

Journal

Micro & Nano Letters

Volume

14

Issue

2

Pages

196 – 201

Description

The results of a comparative investigation on microstructure and magnetic characteristics of silane magnetic nanocomposites coated with silver nanoparticles (AgNPs) are presented. The authors used tetraethyl orthosilicate (TEOS) with (3-aminopropyl) triethoxysilane (APTES) to improve the antibacterial properties of AgNPs. On the basis of this approach, TEOS-APTES polymer was made by the sol–gel method. A layer of the polymer was set on the magnetic core of Fe3O4 NPs and then AgNPs were coated on the TEOS-APTES surface. Therefore, the core–shell structure of the Fe3O4/TEOS-APTES/Ag polymer nanocomposite was synthesised. To characterise the crystal morphology, structure, and size of nanocomposites, various techniques and experiments including Fourier transform infrared spectroscopy, X-ray diffraction, field-emission scanning electron microscope, dynamic light scattering, and transmission

Preparation and structural Characterization of Magnetic NiFe2O4@ABS@Ag nanocompound with Antibacterial Property

Authors

Maryam Mohebbi, Alireza Allafchian, Parviz Kameli, Seyed Amirhoosien Jalali

Publication date

2019/1

Journal

Micro & Nano Letters

Description

The present research attempted to characterize the structural and magnetic characteristics of NiFe2O4@ ABS@ Ag nanoparticles made of nickel ferrite (NiFe2O4), acrylonitrile butadiene styrene (ABS) and nanosilver (Ag Nps), this was done by employing such techniques as X–ray diffraction (XRD), Fourier transform infrared spectroscopy (FT–IR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), as well as vibrating sample magnetometer (VSM). The XRD patterns obtained indicated that following ABS and silver nanoparticles coating, the crystallite size (from scherrer formula) was increased from 32 to 40 nm. It was confirmed by the magnetic measurements that the maximum magnetization of the NiFe2O4 core was dropped when the surface was coated with ABS and Ag Nps. The antimicrobial activity of this threecomponent nanocomposite was tested, showing that the

 

 

کنفرانس ها

امکان پذیری اتصال فاز مایع گذرای فولاد زنگ نزن دو فازی UNS S32750 به فولاد آستنیتی AISI 304

سال انتشار: ۱۳۹۶

محل انتشار: دوفصلنامه علوم و فناوری جوشکاری ایران، دوره: 3، شماره: 2

مشخصات نویسندگان مقاله امکان پذیری اتصال فاز مایع گذرای فولاد زنگ نزن دو فازی UNS S32750 به فولاد آستنیتی AISI 304

  روح الله عبدالوند - دانشکده مهندسی مواد، دانشگاه صنعتی اصفهان، اصفهان، ایران
  مسعود عطاپور - دانشکده مهندسی مواد، دانشگاه صنعتی اصفهان، اصفهان، ایران
  مرتضی شمعانیان - دانشکده مهندسی مواد، دانشگاه صنعتی اصفهان، اصفهان، ایران
  علیرضا علافچیان - پژوهشکده نانو فناوری و مواد پیشرفته، دانشگاه صنعتی اصفهان، اصفهان، ایران

چکیده مقاله:

اتصال فاز مایع گذرای فولاد زنگ نزن دوفازی UNS S32750 به فولاد آستینتی زنگ نزن AISI 304 با استفاده از لایه میانی BNi-2 در دمای 1050 درجه سانتیگراد و به مدت زمان 45 دقیقه انجام شد. ریز ساختار اتصال با میکروسکوپ نوری و الکترونی روبشی مجهز به سیستم آنالیز تفکیک انرژی بررسی شد. به منظور تخمین خواص مکانیکی اتصال از آزمون ریزسختی سنجی و استحکام برشی استفاده شد. در ناحیه ی اتصال هیچ گونه ترکیب یوتکتیکی مشاهده نشد که به معنای کامل شدن انجماد همدما بود. ناحیه ی اتصال از دو قسمت انجماد همدما و منطقه ی متاثر از نفوذ تشکیل شد. استحکام برشی اتصال حدود 0.7 استحکام برشی فولاد زنگ نزن دوفازی بود. بررسی سطوح شکست نشان داد که نمونه متصل شده در زمان 45 دقیقه به صورت نرم شکسته بود.

کلیدواژه‌ها:

اتصال فاز مایع گذرا، فولاد زنگ نزن دوفازی، فولاد زنگ نزن آستنیتی، اتصال غیر مشابه

سنتز و شناسایی ایروژل سیلیسی هیبرید شده با پلی وینیل الکل

سال انتشار: ۱۳۹۷

محل انتشار: اولین کنفرانس ملی میکرو نانو فناوری

مشخصات نویسندگان مقاله سنتز و شناسایی ایروژل سیلیسی هیبرید شده با پلی وینیل الکل

  مهسا سعادتی فر - دانشکده مهندسی نساجی، دانشگاه صنعتی اصفهان، اصفهان، ایران
  زهرا طالبی - استادیار دانشکده مهندسی نساجی، دانشگاه صنعتی اصفهان، اصفهان، ایران
  علیرضا علافچیان - استادیار پژوهشکده نانو فناوری و مواد پیشرفته، دانشگاه صنعتی اصفهان، اصفهان، ایران

چکیده مقاله:

خواص مکانیکی ضعیف و شکندگی ذاتی ایروژل سیلیسی به دلیل تخلخل زیاد ساختار آن، درکنار محدودیت های روش خشک کردن فوق بحرانی، استفاده تجاری این مواد را محدود ساخته است. در این پژوهش، تقویت ساختار و هیبرید سازی شبکه ایروژل سیلیسی با پلی وینیل الکل به منظور سنتز ایروژل هیبریدی پلی وینیل الکل/سیلیکا در شرایط فشار محیط و شناسایی آنها صورت گرفت. ذرات ایروژل سیلیسی هیبریدی در شرایط مختلف به روش سل-ژل دو مرحله ای با استفاده از پیش ماده تترااتیل اورتوسیلیکات TEOS و خشک کردن تحت شرایط محیطی تهیه شدند. در این راستا شرایط مناسب سنتز ایروژل هیبریدی از نظر نسبت مولی مواد، شرایط زمان دهی و اصلاح سطح برای دستیابی به ایروژل هیبریدی با ساختار یکنواخت و چگالی کم و تخلخل بالا تعیین گردید. از آزمون های جذب و واجذب نیتروژن و FT-IR برای شناسایی و ارزیابی خواص ایروژل های خالص و هیبریدی حاصل استفاده شد. نتایج نشان داد مهمترین عامل در ممانعت از جدایی فازی سل سیلیسی هیبرید شده با پلی وینیل الکل، نسبت مولی H2O:Etoh:TEOS است که برابر با 1:7:4 تعیین گردید. ایروژل هیبریدی حاصل از ساختار مزوحفره و سطح مخصوص بالاتر از 530 M2/g برخوردارند. همچنین نتایج بخش بهینه سازی نشان داد که عدم حضور TEOS و آب در محلول زمان دهی، چگالی ایروژل هیبریدی را به 0/64g/cm 3 افزایش و تخلخل آن را به 71% کاهش داده که می تواند ناشی از عدم تقویت کامل ساختار ضعیف ژل هیبریدی در مرحله زمان دهی باشد. اصلاح سطح ژل سیلیسی هیبریدی به کاهش چگالی و افزایش تخلخل آن منجر شد.

کلیدواژه‌ها:

ایروژل سیلیسی، ایروژل هیبریدی، پلی وینیل الکل، جدایی فازی

 

فارسی